Z Auto 2018+ Jeep Wrangler JL & Gladiator JT Tazer Lite Programmer, FedEx 2 Day

Description

Similar to the popular Tazer from Z Automotive for other Mopar vehicles, the Tazer JL LITE is an essential tool for Wrangler JL and Gladiator JT owners. Simple plug and play installation and flashing. There are 2 sets of features- those that want to program the JL or JT to accommodate modifications made to the Jeep and "live" features.
These are all accessed using the factory dash display using the steering wheel buttons to navigate the menus.
Perf Menu:
Adjust for alternate tire sizes up to 42''
Adjust for alternate axle gear ratios
Adjust for an alternate transfer case LO range ratio
TPMS Menu:
Disable TPMS system if desired
Change front/rear TPMS warning PSI limit
Live features - these run only while the tazer is plugged in:
Light shows: Can be accessed from the key fob or from the on-screen menu. 6 pre-set light shows and 3 make-your-own shows included. Set from the factory to only operate when parked, but can be unlocked for off-road and emergency personnel use.
Auto StopStart Disable - can be set to disable AutoStopStart upon vehicle start-up 0-30 and 0-60 timers
AutoPark Disable – can override the AutoPark system
Cooldown mode - run engine fans when Jeep is off, to aid in cooldown
Winch mode – raise engine idle to 2000 RPM while winching or jumping another vehicle Clear Check engine light
AutoTracKill – remembers the last state of the traction control system and sets it for next time.
Rock Crawl: Locks all four brakes with steering wheel buttons to hold the vehicle, especially helpful when off-road.
Winch Mode: Raise idle to 2000 RPM with a simple button press.
Enables sway bar disconnect in 2WD up to 30mph
Line Lock: Locks front brakes for easy burnouts
Display DTC’s – Shows the diagnostic codes that’s making the check engine light come on.
Clear CELs – Reset that pesky check engine light. Good when you have mods that set the light and you know exactly why.
Free USB updates - Past Update List for TaZer Family (Most are for MINI Only, LITE gets very few updates)
10.08.19 - Update 11.1.5
Corrected WinchMode to work on Tazer JL Lite
Added WinchRPM live menu option for Tazer JL Lite
Fixed tire size/gear ratio change from setting DTC
09.03.19 - Update 11.1.4
Added DTC (Engine codes) readout
Fixed “Clear DTC” function to have more comprehensive coverage
Greatly improved ESS memory function reliability
Added Dual Climate control setting for those upgrading from 5″ radio to 7 or 8.4 and swapping in the center stack switch assembly with volume knobs
Fixed Winch Mode
Fixed Halo Enable function
Added ability for Rubicon fenders DRL’s to be used on Sport
05.15.19 - Update 11.1.2
Added live function to remove “Service AWD” message when deleting lockers for Rubicon axle swaps
05.08.19 - Update 11.1.1
Added live menu item to allow adjustment of Winch Mode idle speed.
04.12.19 - Update 11.1.0
Added support for using aftermarket LED front turn signals and taillights on LED or non-LED equipped Jeeps. This deletes the “bulb out” messages and hyperflash sense circuit. (this version will report as 11.1.0 in ZPU but 11.0.9 on the dash)
03.18.19 - Update 11.0.9
Added some functions for customer support use; user experience same as 11.0.8
02.28.19 - Update 11.0.8
Locker control in any mode, even front locker only.
Full Traction/ABS/ESP kill.
Sway bar kill at any speed.
Cruise button remapping.
Hood alarm.
Corrected tire size selections.
Added LED Headlight option.
Added Halo BCM output to Halo on/off function.
Added DTCM option and FAD delete separately in “off road” settings to cover more axle swap choices.
ESS Kill and TracKill removed from live options, now will remember last state when shut down.
Tweaked TurnCam for better reliability.
Added ParkSense options.
Fixed Marry/Unmarry function to not display “try again” message, as it will automatically re-try and succeed.
Made changes to Nav In Motion to reduce reboots after startup.
Added many safeties for going to sleep no matter what mode it’s in when the Jeep is turned off.
Lowered sleep current from 38mA to 7mA, making it insignificant.
Stability fixes.
08.20.18 - Update 11.0.6
Live menu additions: AutoPark disable and TurnCam (rear camera on with turn signals).
Settings menu, added PanicButton disable.
Fixed Aux button enable.
Fixed ESS disable to engage quicker and reliably. If marry/unmarry is ignored by BCM, will now say “try again” instead of “FAIL”.
05.09.18 - Update 11.0.2
Added sway bar disconnect in 2WD, split “other” into “off-road” and “other” submenus.
Added one-touch lane change on/off
EPS delete
Seat belt ding disable
fixed force camera so blind spot isn’t affected (from 11.0.2), improved R/W routines